Language
Precautions for installation of semi-automatic copper rod butt welding machine
Wuxi Xinxing Welding Equipment Factory mainly produces: spot welding machines, butt welding machines, flash butt welding machines, medium frequency spot welding machines, energy storage spot welding machines, nut spot welding machines, polymer diffusion welding machines and other resistance welding equipment! QQ online consultationSitemapContact us
Xinxing. Intelligent resistance welding equipment and solution service provider 33 years of deep experience in the industry help companies solve difficult welding problems and improve welding efficiency!
National service hotline:400-001-050213395100070
Precautions for installation of semi-automatic copper rod butt welding machine
Release time:2022.02.26
Summary of information:
The semi-automatic copper rod butt welding machine has been fully assembled before leaving the factory. Generally, there are no accessories that need to be assembled. The installation is very simple. You only need to connect the power cord, but there are still many other precautions. Please read it carefully before installation. 1. First of all, after receiving the product, check the welding machine inside and out.
hereSemi-automatic copper rod butt welding machine is Xinxing Welding’s UN2SCNC mobile butt welding machine, it has been fully assembled before leaving the factory. Generally, there are no accessories that need to be assembled again. The installation is very simple. You only need to connect the power cord, but there are still many other precautions. Please read it carefully before installation.
3. Check whether all fasteners of the welding machine are loose or falling off to prevent injuries to people and other objects during lifting and moving.
4. For the driving sling, choose a special rope that can withstand 15 times the weight of the welding machine.
5. Sufficient room should be left in the hanging and vertical and horizontal operating spaces of the welding machine to prevent collisions and damage to equipment and components.
6. Check whether the air switch and fuse of corresponding capacity are installed in the electrical cabinet. If not, install the corresponding circuit breaker according to the rated input current data provided on the welding machine nameplate.
7. Install and operate the AC380V power supply according to the nameplate and strictly follow the safety regulations
8. The welding machine must be reliably grounded, and the cross-section of the grounding conductor should not be less than 4mm2. Otherwise, an unexpected failure may cause electric shock.
9. Generally, the cross-section of power supply wire is selected according to 8A/mm2. For 25KVA power cord, 4-6mm2 is recommended, and 6mm2 is recommended. For 50kva power cord, 10-16mm2 is recommended, and 16mm2 is recommended.
Xinxing welding equipment factory, focus onResistance welding machine29 years of research and development, production and sales, whether it is a manual butt welding machine, a semi-automatic butt welding machine, an automatic butt welding machine, a medium frequency butt welding machine, a foot-operated spot welding machine or a pneumatic spot welding machine, a medium frequency spot welding machine, an automatic spot welding machine, an AC seam welding machine or a DC seam welding machine. Machines, butt welding brazing machines or spot welding brazing machines are all loved by new and old customers because of their high quality, suitable for workpieces, high efficiency and reasonable prices. If you are also interested in our welding equipment, please contact us: 400-001-0502.
1. First of all, after receiving the product, check all the parts of the welding machine inside and out to see if there are any bumps or scratches during the logistics process. If so, contact the supplier to solve these problems first.
2. Check to see if the instructions and certificate are there. If not, contact the supplier to provide them.3. Check whether all fasteners of the welding machine are loose or falling off to prevent injuries to people and other objects during lifting and moving.
4. For the driving sling, choose a special rope that can withstand 15 times the weight of the welding machine.
5. Sufficient room should be left in the hanging and vertical and horizontal operating spaces of the welding machine to prevent collisions and damage to equipment and components.
6. Check whether the air switch and fuse of corresponding capacity are installed in the electrical cabinet. If not, install the corresponding circuit breaker according to the rated input current data provided on the welding machine nameplate.
7. Install and operate the AC380V power supply according to the nameplate and strictly follow the safety regulations
8. The welding machine must be reliably grounded, and the cross-section of the grounding conductor should not be less than 4mm2. Otherwise, an unexpected failure may cause electric shock.
9. Generally, the cross-section of power supply wire is selected according to 8A/mm2. For 25KVA power cord, 4-6mm2 is recommended, and 6mm2 is recommended. For 50kva power cord, 10-16mm2 is recommended, and 16mm2 is recommended.
Xinxing welding equipment factory, focus onResistance welding machine29 years of research and development, production and sales, whether it is a manual butt welding machine, a semi-automatic butt welding machine, an automatic butt welding machine, a medium frequency butt welding machine, a foot-operated spot welding machine or a pneumatic spot welding machine, a medium frequency spot welding machine, an automatic spot welding machine, an AC seam welding machine or a DC seam welding machine. Machines, butt welding brazing machines or spot welding brazing machines are all loved by new and old customers because of their high quality, suitable for workpieces, high efficiency and reasonable prices. If you are also interested in our welding equipment, please contact us: 400-001-0502.
Hot product recommendations
-
300KVA copper bar soft connection diffusion welding machine
Power: 300KVA Model: DBTH-300 Overlap: Copper skin, copper strip, copper foil soft connection, stainless steel, etc., and can also weld dissimilar materials. The hydraulic high-power medium-voltage medium-frequency copper bar soft connection diffusion welding machine mainly welds the same multi-layer copper strip, copper foil and copper skin into soft and hard copper bar connectors. It can also weld stainless steel strips, titanium zirconium and tantalum strips and multi-layer dissimilar materials. Mainly used for conductive connections in new energy vehicles, electric power stations, electrical switches, smelting power supplies, welding machines and other industries.
-
150KVA copper strip soft connection diffusion welding machine
Power: 150KVA Model: DBTH-150 Overlap: soft connection of copper skin and copper strip, stainless steel, etc., and can also weld dissimilar materials. The variable frequency polymer diffusion welding machine is a welding method that brings the surfaces of workpieces into contact with each other under a certain temperature and pressure, causing a fine liquid phase to be produced on the surface of the workpiece and gradually diffusing each other to achieve bonding. It is mainly used for soft connections of new energy vehicle batteries, soft copper bar connections of power supplies, secondary output connections of large power supplies in petrochemical industry, smelting, welding machine connection copper strip joints, etc.
-
SUN pneumatic automatic flash butt welding machine
1. Originated in 1993 2. Xinxing’s 26-year history 3. Always adhere to all-copper welding machines 4. 10-year long design life 5. 20-year service life record 6. Serve 4000+ customers 7. CQC certified products
-
UN6 flash pneumatic resistance butt welding machine
The UN6 flash pneumatic resistance butt welding machine is widely used in the butt jointing of various metal round materials, flat materials, and pipes. With different special molds, it can also weld various special-shaped materials and copper and aluminum pipe joints. The UN6 flash pneumatic butt welding machine adopts pneumatic clamping and pneumatic transverse upsetting. It is also equipped with a special butt welding controller, which can accurately adjust the welding current and welding time. The welding output can be configured as required and adopts two control methods, primary voltage feedback and secondary current feedback, to ensure consistent welding current. Just step on the foot switch to complete the entire welding process. The machine has a high degree of automation and stable welding quality. Compared with the previous standard version, the welding stroke limit and upsetting air pressure conversion functions have been updated. The non-standard version is controlled by PLC programmer, and can be equipped with optional tempering device, ejector cylinder, and positioning cylinder auxiliary action. In addition to the above extended functions, the high-end version adopts modular design and linear guide rail guidance for higher precision and easier maintenance. Please read below for advantages and features
-
DBZ medium frequency resistance spot welding machine
Xinxing medium frequency inverter pneumatic resistance spot welding machine is a three-phase alternating current that is rectified into DC, and then through an inverter circuit composed of IGBT power devices, it is converted into an intermediate frequency 1000-4000HZ AC square wave output. After being stepped down by a transformer, it is rectified into DC and supplied to the electrode for welding the workpiece. Current feedback and pulse width modulation (PWM) are used to obtain stable current output. It is one of the cutting-edge resistance welding methods today. The medium-frequency resistance spot welding machine can be used for spot welding and multi-point projection welding of ordinary low carbon steel plates, stainless steel plates, galvanized sheets, aluminum plates and wires. It can also be used for spot welding and nut projection welding of high-strength steel and hot-formed steel in the automobile manufacturing industry, as well as resistance brazing and spot welding of copper wires in the high and low voltage electrical industry, brazing of silver points and copper plates, composite silver point welding, etc. Please read below for advantages and features
-
Semi-automatic CNC UN2S copper rod resistance butt welding machine butt welding machine
1. This series of products ranks top 2 in the national market share 2. Originated in 1993 3. Xinxing’s 28-year history 4. Always adhere to all-copper welding machines 5. 10-year long design life 6. 20+ years service life 7. Serve 5000+ customers 8. CQC certified products 9. 90% repeat customers
-
160KVA copper stranded wire pneumatic butt welding machine
Model: UNG-160 Power: 160kva Butt: 50~300 square meters of copper stranded wire, aluminum stranded wire, copper rod, aluminum rod 160KVA copper stranded wire butt welding machine adopts pneumatic pressurization, photoelectric positioning, touch screen programming control, water cooling, low-voltage and high-current intelligent resistance welding machine, and welds copper multi-strand wires and aluminum multi-strand wires with sleeves Wire, stranded conductor, welded firmly in 2 seconds, smooth and without flash. Please read below for advantages and features
-
UNG precision multi-stranded copper wire butt welding machine
Model: UNG-5 Power: 5Kva Suitable for: rapid welding of multi-stranded conductors, copper strands, tinned copper strands, and aluminum strands in wire and cable factories. The UNG precision multi-stranded wire butt welding machine is a single-phase AC resistance butt welding machine. This welding machine is mainly used for welding multi-strand conductors in the wire and cable industry. It is used with casings and is welded and formed in one go. The joints are strong and beautiful, with no flash or burrs, and the wire diameter does not change. It can be directly threaded through the mold, so that the production can be changed without stopping the machine.
-
CNC type UNG multi-stranded wire butt welding machine butt welding machine
Model: UNG-5 Power: 5KVA CNC UNG multi-strand wire butt welding machine belongs to the single-phase AC resistance butt welding machine category. This welding machine can butt weld 0.75-10 square meters of copper multi-stranded wires, 4-16 square meters of aluminum multi-strand wires and various metal wires, such as steel wires, copper wires, aluminum wires, titanium alloy wires, etc. It is suitable for the welding of round rods and small wires in wire drawing, cable and metal wire processing industries. 1. Xinxing’s 30-year history 2. Always adhere to all-copper welding machines 3. 10-year long design life 4. 20+ years of service life 5. Serving 11,000+ customers 6. CE certified products 7. 90% are repeat customers
-
50KVA pneumatic multi-stranded wire butt welding machine
Model: UNG-50 Power: 50KVA Butt connection: 16-120 square copper stranded wire, 25-120 square aluminum stranded wire, tinned stranded wire φ4-12 copper rod φ4-16 aluminum rod Pneumatic multi-strand wire butt welding machine is one of the resistance welding machines (butt welding machines). A pneumatic butt welding machine developed by Xinxing Welding Equipment Factory in 2005. It adopts pneumatic clamping and pneumatic transverse upsetting, and is equipped with an internal and external full water cooling system and a special butt welding controller, which can accurately adjust parameters. At the same time, it can be used with casings to weld multi-core wire harnesses and single-core copper wires without burrs.
News·Information
Contact Xinxing
- After-sales phone number:400-001-0502
- Pre-sales phone number:199-5222-1801
- Email:cnhjsb@163.com
- Address:Next to Huaming Bridge, 161 kilometers away from National Highway 312, Luoshe Town, Huishan District, Wuxi City, Jiangsu Province
Wuxi Xinxing Welding Equipment FactoryAll rights reserved
Su Public Network Security No. 32020602001105Su ICP No. 11039752
Service hotline 400-001-050213395100070 new manager
Email:cnhjsb@163.com
Factory address: Huishan District, Wuxi City, Jiangsu ProvinceHuamingqiao Industrial Zone, 161 kilometers away from National Highway 312, Luoshe Town, Huishan District, Wuxi City, Jiangsu Province
Follow the public account
Official WeChat
QR code
Troubleshooting tips for iron ring and copper ring pneumatic butt welding machine
Summary of information:
The iron ring and copper ring pneumatic butt welding machine is an intelligently controlled resistance welding machine produced by Xinxing Welding. The operation is very simple. However, some corporate customers may have some malfunctions due to improper operation when personnel are changed, causing the welding machine to light up and prompt. What are the meanings and solutions of the prompts?
The iron ring and copper ring pneumatic butt welding machine is an intelligently controlled resistance welding machine produced by Xinxing Welding. The operation is very simple. However, some corporate customers have some malfunctions due to improper operation when personnel are changed, causing the welding machine to light up and prompt. What are the meanings and solutions of the prompts?
They are divided into1-8The serial number represents:
|
serial number |
ContainsRighteousness |
Fault display reason |
solutionSolution |
|
1 |
Thyristor pass-through |
When the controller has no output, it detects that the thyristor single or double tube is conductive. |
1、 Check whether the thyristor is damaged 2、 Is the wiring correct? |
|
2 |
The thyristor does not conduct |
When the controller outputs pulses, it detects that the thyristor single or double tube is cut off. |
1、 Check whether the thyristor is damaged andAre the wiring of terminals 3, 4, 5 and 6 correct? 2、 Please power on the controller7.8 wiring swap |
|
3 |
passedhot |
When an external thermal protection switch is connected, the switch operates or is abnormal. |
1. Whether the thermal protection device operates (whether it is really overheated) 2. Is the AA setting correct? |
|
4 |
Overcurrent |
Welding current is too large |
1、 Is the AH setting correct (for example, the parameter setting is too small) |
|
5 |
Undercurrent |
Welding current is too small |
1、 Is the AL setting correct (for example, the parameter setting is too small) 2、 The workpiece is not placed properly or the contact is not good 3、 The current setting value exceeds the maximum current of the transformer |
|
6 |
Transformer range is too large |
Sampling current is small |
Replace the transformer with a smaller range |
|
7 |
Memory data error |
Controller parameter settings are incorrect |
Check parameter settings |
|
8 |
no sync signal |
Sync signal lost |
1. Check whether the wiring matches the wiring diagram 2、Please also add7 and 8 are swapped, 3 and 4 are swapped with 5 and 6 (i.e. 3 and 5 are swapped, 4 and 6 are swapped) |
Wuxi Xinxing Welding Equipment Factory was established in1993year,Focus on resistance welding machines30year,Production products include:Butt welding machine,Pneumatic butt welding machine,Flash butt welding machine,Hydraulic butt welding machine,Copper and aluminum pipe butt welding machine,Automatic butt welding machine, spot welding machine,Pneumatic spot welding machine,Medium frequency spot welding machine,Energy storage spot welding machine,Precision spot welding machine,Automatic spot welding machine,Projection welding machine,Frequency conversion projection welding machine,Medium frequency projection welding machine,Array welding machine,Fully automatic welding production line,seam welding machine,Medium frequency seam welding machine,Resistance brazing machines and supporting printers, spark testing machines, high-voltage testing machines, wire pay-off machines, etc.300Various,Long-term cooperative customers reach5000Multiple,The quality is comparable to that of major imported brands. Welcome to learn more and purchase.!
Hot product recommendations
